樂泰 EA 9017

樂泰 EA 9017

Applications:Structural bonding
固化類型：室溫（環境）固化
Key characteristics:Cure speed: fast cure; Strength: high strength
組件數量：2件
物理形態：液體
Recommended for use with:Ceramic; Concrete; Glass; Plastic; Wood

概述

樂泰 EA 9017 是 two-component structural epoxy adhesive 專為 demanding assembly, maintenance and repair applications. It cures to a rigid, tough bond line that delivers high strength, good gap-filling and long-term durability on a wide range of substrates.

Once cured, Loctite EA 9017:

  • 提供 strong adhesion on properly prepared metals and composites

  • 填充物 小縫隙和表面不規則 without running

  • 形成 tough, impact- and vibration-resistant joint

  • Offers good resistance to typical oils, moisture and industrial environments

It’s a solid choice when you want to 補充或更換機械緊固件 and improve stiffness and reliability in your assemblies.

主要功能與優勢

  • 雙組分結構環氧樹脂
    樹脂與硬化劑反應形成 剛性高強度黏合劑 for structural and semi-structural joints.

  • 間隙填充、無縫隙稠度
    Paste-like formulation 停留在你塗抹的位置, including on vertical surfaces, and bridges machining marks and minor misalignment.

  • 多基板黏著力
    債券 鋼、鋁、許多塗層金屬、複合材料和特定工程塑料 (always pre-test critical plastics and finishes).

  • Tough, durable bond line
    Designed to withstand vibration, impact and thermal cycling better than brittle adhesives.

  • 室溫固化
    治療方法 環境溫度 after mixing; in many processes, 中火 (if allowed by the design) can be used to accelerate cure.

典型應用

Loctite EA 9017 is commonly used in:

  • 金屬與複合材料組件

    • 黏合 支架、肋條、加強筋與嵌件

    • 將複合材料蒙皮接合至金屬或複合材料框架

  • 工業設備與機櫃

    • Bonded covers, panels and machine guards

    • Frames, housings and bases exposed to 震動與處理

  • Maintenance & repair

    • Rebuilding or reinforcing non-critical metal parts

    • 替換或備份 焊縫、螺絲與鉚釘 in assemblies

For safety-critical structures, always validate joint design, preparation and cure schedule with appropriate testing and approvals.

How to Use Loctite EA 9017

步驟 1 – 表面處理

  1. 確保所有接合面 清潔、乾燥且結構完好.

  2. Remove loose paint, rust, scale and weak coatings.

  3. 脫脂以去除 油、油脂、切削液及脫模劑.

  4. For high-strength joints, 輕微磨損或噴砂處理, followed by cleaning, is recommended.

步驟二 – 混合

  1. 將兩個組件均加熱至建議的工作溫度。.

  2. 將樹脂與硬化劑按指定比例混合 混合比例（按重量或體積）.

  3. Stir thoroughly, scraping sides and bottom of the container until the mix is 色澤均勻.

  4. 避免困住過多空氣並尊重 可用罐壽命 – only mix what you can apply in time.

  5. If supplied in dual cartridges, purge both sides, attach a 靜態混合噴嘴, and discard the first small bead before use.

第三步 – 申請

  1. 套用一個 連續、均勻的珠狀或層狀 將混合黏合劑塗佈於一個或兩個表面。.

  2. 確保完全覆蓋接合區域，並預留足夠的材料以 wet the surfaces and fill minor gaps.

  3. 將零件組裝於黏著劑內 工作時間.

步驟 4 – 組裝與固化

  1. Position parts accurately and apply 輕型夾具或定位裝置 以維持對齊與膠合線厚度。.

  2. Do not over-clamp; aim for a thin but continuous bond line, not a starved joint.

  3. 讓黏著劑 常溫固化 直至達到可處理強度。.

  4. If the design permits, 中火 may be used to accelerate cure and reach full strength sooner.

步驟五 – 完成

  1. 去除多餘部分 未固化 使用適當溶劑與乾淨布料清除黏著劑。.

  2. 一旦完全固化，黏著劑便無法移除 機械地 (刮削、打磨、機械加工).

  3. 固化後的接頭通常可以 鑽孔、機械加工及噴漆 按要求。.

安全與操作

  • 避免 皮膚與眼神接觸 與未固化的樹脂和硬化劑一起使用；環氧樹脂和固化劑可能會造成刺激或過敏。.

  • 用於 通風良好 區域，並避免吸入加工固化材料時產生的蒸氣或粉塵。.

  • 穿著得體 個人防護裝備：防化手套、安全眼鏡和防護服。.

  • 請勿將未固化的材料排入 排水溝或天然水道; ；依照當地法規處理廢棄物。.

  • 將元件儲存在其 原始、密封良好的容器 存放於陰涼乾燥處，遠離熱源及火源。.

請務必參閱最新版本 安全資料表 (SDS) and technical data for Loctite EA 9017 before use.

常見問題

Q1: What is Loctite EA 9017 mainly used for?
Loctite EA 9017 is mainly used for structural and semi-structural bonding of metals and composites where high strength and gap filling 是必需的。.

Q2: Does Loctite EA 9017 cure at room temperature?
是的，它的設計目的是 在室溫下固化 經適當混合後。在設計允許的情況下、, 適度加熱 can be used to shorten cure time.

Q3: Can EA 9017 replace welds or mechanical fasteners?
在某些設計中，它可以 reduce or partially replace welds, bolts and rivets, but this must be confirmed by engineering analysis and testing. Many users combine adhesive bonding with fewer fasteners for redundancy.

Q4: Can Loctite EA 9017 bond plastics as well as metals?
它能將許多事物結合在一起 工程塑料, 但性能取決於具體的聚合物和表面處理方式。低表面能或極具柔韌性的塑料可能需要特殊處理或更換黏著劑。請務必 測試您的精確基質.

Q5：膠合線的厚度上限是多少？
EA 9017 has 良好的填補能力, but very thick sections cure more slowly and may affect final properties. Design for a 受控膠合線厚度 根據您的技術指導。.

Q6：固化後的黏合劑是否具有彈性？
Once cured, Loctite EA 9017 forms a 剛性結構鍵合 with some toughness for impact and vibration, but it is not a soft, highly flexible sealant.

Q7: How can a joint bonded with EA 9017 be disassembled?
固化結構環氧樹脂是 難以去除. Joints typically must be cut, ground or machined apart, and, where allowed, gently heated to help release them. Plan service and repair strategies during the design phase.

相關商品